Version Report Firmware

COMmander¬ģ Basic


Version Changes

2.2E
(13. 03. 09)

Troubleshooting:

  • Sporadically it came to phantom entries in the calling data list of the pbx. This behavior was corrected.
  • A call to an activated Call Forwarding over the provider doesn't work sporadically, if the call came from an analogue exchange. This function was adapted.

2.2 D
(14. 01. 09 )

New features:

  • COMfortel 1100 implemented.

Troubleshooting:

  • A pickup from a call to an Auerswald Box was faulty. The laudness in the receiver was too quiet and you can hear the call signal. These function was corrected.


2.1 F
(11. 02. 08)

Troubleshooting:

  • After the 01.01.2010 the date was counted correctly too.


2.1 E
(14. 12. 07)

Troubleshooting:

  • Problems with Boss/Secretary Function unfixed.


2.1 D
(07. 12. 07)

New features:

  • The update-intervals were enlarged.
    Minimum and default value is now 6 month.
  • For supporting the power-saving-function of the system phones the layer 2 on the internal S0 busses was shut down.

Troubleshooting:

  • It could be, that the speach to the other subscriber was switched delayed.
    This behaviour was corrected.


2.0 E
(27. 02. 07)

Troubleshooting:

  • At different Siemens isdn DECT telephone systems which were used on an Auerswald COMpact system, it could happened that after a time no calls were possible on the Auerswald COMpact System. This behaviour of the DECT Systems was adapted.
  • The adjustment with the COMfort- and COMfortel phones was restyled.
  • If a subscriber with a direct exchange line access was called over different lines (p.e. analogue gateway, call through, automatic reception...) there was a wrong call number displayed on the called telephone. This was corrected.

2.0 C
(18. 08. 06)

Troubleshooting:

  • Problems with transfer from the telefone book of the pbx to the COMfort phones resolved.


2.0 B
(14. 08. 06)

New features:

  • COMfortel 1500 and 2500 implemented.

Troubleshooting:

  • Distribution of the firmware for the COMfort-/COMfortel phones improved.
  • Switch on/off of the external call forwarding from the door terminalwith the telephone corrected.

2.0 A
(06. 06. 06)

New features:

  • COMfortel DECT 900 implemented.

Troubleshooting:

  • Subscriber-Call forwarding with a COMfort phone and activated LCR corrected.
  • Fallback from fax G4 to fax G3 for internal fax-communication corrected.

1.8 D
(13. 01. 06)

New features:

Adaptions at the exception numbers for the VoIP Routing
Note!
Changed/adjusted behaviour!!! The configuration in COMset (Properties of the subscriber --> Exchange line settings) "Call setup via VoIP/GSM" was extendet. Now also VoIP/GSM adapters at the S0 Bus were account.

  • The automatic reception can now be switched on or off configuration dependent with a programming code. The handling is discribed in the manual (Version 18 12/05).

Troubleshooting:

  • Rechnungsdruck bei der Hotelfunktion korrigiert.
  • "Check in" uad "check out" in the hotelfunction restyled.
  • B-chanal reservation corrected.
  • Notruf bei eingeschr√§nkter Amtberechtigung nun auch mit Amtsholung √ľber 0 wieder m√∂glich.
  • Der Besetzton ist jetzt wieder zu h√∂ren, wenn bei einer externen Teilnehmer Anrufweiterschaltung der Zielteilnehmer besetzt ist.
  • Amtbelegung bei einer Teilnehmer Anrufweiterschaltung ist korrigiert, wenn mehrere externe So angeschlossen sind.
  • LCR is now activ at a subscriber call forwarding.
  • Automatc clock time adjustment restyled.
  • Amtreservierung √ľber Nachwahl der Ziffer 2 mit einem COMfort 2000/1200/1000 oder Teilnehmer mit direktem Amtapparat wieder m√∂glich.
  • Teilnehmer Anrufweiterschaltung mit Kurzwahl als Zielrufnummer wird jetzt wieder ausgef√ľhrt.
  • Text Ansagen vom Amt, wie z.B. "Kein Anschluss unter dieser Nummer", werden wieder durchgeschaltet.
  • Amtberechtigung Notruf wurde √ľberarbeitet.
  • Call-Through calls  were now correct used over VoIP Routing.
  • Number for Anny-Way in SMS-Centers changed to 09003266900.
  • Second doorbell function was corrected.

1.8 C
(12. 10. 05)

Troubleshooting:

  • Some PBXs could not be called after updating the system. This has been fixed.

1.8 B
(22. 08. 05)

Troubleshooting:

  • Possibility of system-reset during exchange access with few number digits fixed.
  • Error in busy on busy function in combination with call forwarding fixed.
  • System telephones did not ring with a firmware version older than 2.0 H.

1.8 A
(05. 08. 05)

New features:

  • Implementations for Italy.
  • CNIP for Belgium an Germany.
  • Automatic reception implemented (Firmware 1.8 A or better required).
  • Time setting "unanswered call transfer" (Firmware 1.8 A or better required).
  • Setting "do not accept ISDN charging informations" (Firmware 1.8 A or better required).
  • Setting "do not accep tISDN time/date informations" (Firmware 1.8 A or better required).

Troubleshooting:

  • Fehler in der Rufnummern√ľbermittlung bei Tn AWS behoben.
  • Fehler in der Rufnummern√ľbermittlung bei ext. Apothekerschaltung beseitigt.
  • Schnellere √úberpr√ľfung ob Amt belegt ist: Ohne VOIP und GSM Gateway Definition kommt der Besetztton jetzt schneller, wenn alle B-Kan√§le zum Amt belegt sind.
  • Busy on Busy geht jetzt auch bei eingeschalteterTN AWS
  • Das Auflegen des B-Teilnehmers in internen R√ľckfragegespr√§chen, die durch Pickup angenommen wurden, konnte zu Gespr√§chstrennungen f√ľhren.

1.7 C
(22. 06. 05)

Troubleshooting:

  • Subscriber-Call forwarding fixed.
  • CLIP function during Subscriber-Call forwarding now again possible.
  • Keypad again available.
  • Programming from direct exchange line subcribers now again possible.
  • LCR-blocking revised.

1.7 A
(06. 06. 05)

New features:

  • VoIP-GSM-Routing implemented (configurable from Software 2.5.25 on).
  • Calling line presentation for external door line can be configured.
    (configurable from Software 2.5.25 on).

Troubleshooting:

  • Internal call waiting tone for internal subscribers and groups revised.

  • Verbinden von zwei ext. Gespr√§chen aus der Konferenz nun m√∂glich.


1.6 F
(04. 05. 05)

Troubleshooting:

  • Problems while storing/recording Text before answering fixed.


1.6 E
(10. 01. 05)

Troubleshooting:

  • Call querry function revised..
  • Subscriber signalization fixed.

1.6 D
(17. 12. 04)

New features:

  • Internal waiting call notification. If an internal call reaches a busy subscriber, witch has allowed the waiting call signalling, the caller firs receives a busy tone, but after five seconds of time the busy subscriber will be notificated about the waiting call. A condition is that the busy subscriber does not have calls in hold-position.

Troubleshooting:

  • In the hotel function the waking time can be set only by a room telephone, if the guest has already checked in.
  • For a subscriber with direct exchange line access "**" is placed in front of the transmitted caller ID. This is displayed also at analogue devices now.
  • The presentation of the caller ID has been revised (for a COMfort 1000, 1200 and 2000).

1.6 A
(16. 10. 03)

New features:

  • COMfort DECT-support implemented.
  • Hotel functions.
  • "Text before answering is now switchable by function key of a COMfort 1000, 1200 or 2000.
  • Note: For the settings and the operation of this new fatures you need the following Software releases: COMset 2.5.6 or better, COMfort Set 1.3.37 or better, COMtools 2.2.51 or better and the telephone-firmware 2.0G or better.

Troubleshooting:

  • Voice Mail Center 461: Mailbox access reworked.
  • Access to the externeal switch corrected.
  • Occasional break-up of incoming calls without DDI from point to point switches fixed.

1.5 S
(28. 07. 03)

New features:

  • CLIP-Alphanumeric (analog). This release provides "number to name" on analog telephones based on the central phonebook of the PBX.

Troubleshooting:

  • Problems with the activation of the external line fixed. In some cases only the second attempt was successfull.
  • Soft-LCR easy optimized. If there were problems with the Teledata-update server, renewed access attempts could appear. This has been fixed.
  • Soft-LCR easy-update in spite of Soft-LCR 3.0 usage removed.
  • Missing CLIP informations (analog). Some devices (e.g. AEG Ascona) could not screen the CLIP information. This has been fixed.
  • Connection delay with incoming calls removed.

1.5 R
(06. 06. 03)

Troubleshooting:

  • False dialling of a/b-adaptors has been fixed.


1.5 Q
(23. 05. 03)

New features:

  • CLIP-Telephones now always start ringing with the CLIP-Header no matter, whether CLIP-Information is going to be transmitted, or not.
  • In Soft-LCR Easy starting from V 1,3,7 the selection item "use, also in the local area network (Verwenden, auch im Ortsnetz)" is supported.
  • Extended support of call by call in the local area network. There are provider, whitch do not offer their call by call services nation-wide. Therefor the Teledata update-server is not able to select the provider for every single local network. So the possibility to select the provider manually was generated.
  • CCNR (Call completition on no response) in the external exchange is supported now. The setup with the COMfort-Telephones is similar to the internal CCNR.

Troubleshooting:

  • CLIP has been revised.
  • Partially the outgoing MSN was not displayed in the charge record. This has been fixed.
  • LED-control for configuration change-over has been reworked.
  • Entry of calling data after LCR-update - If a LCR-Update has been carried out, no internal subscribers were transmitted to the record. The behaviour of the PBX was revised to the effect that the subscriber data will be transmitted to the record now.
  • CGPN at PTP-switch - Now the complete subscriber number is going to be transmitted to the external exchange instead of only the DDI on an outgoing call, because some switches and provider could not handle it.

1.5 P
(12. 03. 03)

New features:

  • Further waiting-field-subscribers implemented.
    With this release the COMmander Basic supports up to four waiting-field-subscribers are available for the waiting field. Each subscriber can log in/out on his own.
  • Outgoing calls out of the waiting field can be parked.
  • Call by call in the local exchange
    With this release Soft-LCR supports real call by call in the local exchange. From May 2003 on the first providers will prospectively provide appropriate rates.
  • CLIP-waiting time
    This release prevents the waiting time of 10 seconds at devices with activated CLIP-function. This is necessary to signal two calls in serie with less than 10 seconds of spacetime. In this case the second caller became a busy signal. The CLIP-waiting time can be deactivated in COMset.
  • Fallback of exchanges without query
    An exchange without query is not going to be disconnected, if it fallsl back on the intermediately busy initiator. It is tried to be connected, untill the initiator is available again.
  • Default values for the call data record have been extended.
    - Connections free of charge will not be saved
    - Unsuccessful outgoing calls will not be saved
    - Incoming successful calls will not be saved
    - Inciming unsuccsessful calls will not be saved
    - Call data record does not change with the subscribers


Troubleshooting:

  • Waiting music recording via audio in socket has been corrected.
  • After a pick up the caller number will be displayed.
  • Modification in the default values of the automatical firmware update: minimum interval for the firmware update is now every 12 weeks.

1.5 O
(28. 11. 02)

New features:

  • During a check up of our update server we discovered periods with a concentration of incoming customer calls. To solve this, we spread the update period by random generation.

Troubleshooting:

  • Some systems could not be updated because of tolerances of several components. This was fixed.
  • Sporadically transferterminations could occur, when 99% were reached. This behaviour was corrected.

1.5 N
(25. 10. 02)

Troubleshooting:

  • In case of delayed external calls invalid connection data was stored sporadically. This was fixed.


1.5 L
(27. 09. 02)

New features:

  • Automatically colockset.
    In the delivery state of the COMmander Basic the internal clock was synchronized by calling "01191" (time announcement of the Telekom). Since user of this service is liable to pay for it, the number is not preset anymore.
  • Completion of calls to busy subscribers (CCBS) was displayed as a menu item in the system telephone. With this modification it will only be displayed, if the feature is available in the external exchange.

Troubleshooting:

  • Calling line identification can now be restricted for SMSs.
  • The Siemens Gigaset 3035/3075 reacts incorrect in case of two consecutively incoming calls (The second call is not acknowledged). After this modification the telephone acknowledges and signals the second call.
  • If no internal S0-Bus is present, the PBX crashes after 1 hour and 24 minutes. This behaviour was fixed.

1.5 K
(23. 06. 02)

New features:

  • All waiting-line-subscribers receive only one "Text before answering". Afterwards they hear the music on hold. If the "Text before answering is allready running, when a call comes in, the caller hears music on hold until the text is finished. Afterwards all subscribers waiting for "Text before answering are switched on this text.
  • Group subscribers can now be logged in with the COMset 2.3.39.

Troubleshooting:

  • If no COMfort 1000, 1200, 2000, or no updatable telephone is connected to PBX, break of connections could occure. This problem was solved.


1.5 I
(29. 03. 02)

New features:

  • Boss/Sekretray-function.
  • Waiting field.
  • Call through to internal subscribers.
  • SMS in fixed networks.
  • Number to name function for the systemdisplay integrated.

Troubleshooting:

  • Phonebook actualizing speed of the COMfor-telephones increased.


1.5 H
(18. 12. 01)

Troubleshooting:

  • Firmware-update-management revised.
  • The period for the automatically firmware-update was changed. The following spaces of time are now eligible:
    - 4 weeks
    - 12 weeks
    - 6 months
    - 1 year
    From COMset Volume 2.3.19 on the periods one and two weeks were removed.They were extended from one and two weeks up to four weeks. The setting "every twelve weeks remained unchanged. The execution of the automatically software-update every six months and one year can only be used with COMset 2.3.21 or better.

1.5 G
(14. 12. 01)

New features:

  • Call Through
    The configuration of call through is to be made with the application COMset (from2.3.19 on). Additionally COMtools (from 2.32.26 on) is necessary to permit the release for incomming callers via shortcodes.
  • Automatical firmware-update. The PBX can now carry out a periodical firmware-update automatically. Setup with COMset 2.3.19 or better. The telephones can be updated simultaneously. (Telephone firmware 2.0 A or better).
  • The following settings in the COMfort 2000, made with COMfort Set so far, are now implemented to COMset:
    - Call protection
    - Call-waiting signal permission
    - VIP/Robinson-activation
    - direct exchange line access
    - InterCom permission
    Note: In theCOMfort 2000 the firmware 2.0B or higher must be loaded. This update will be available in the next weeks.
  • Soft-LCR easy can be used.
    Selected providers are displayed in the system telephone.
    Note: Soft-LCR 3.0 or better can be used furthermore. It must be presetted, which of both programs is to be used. With Soft-LCR 3.x the display message is not available.
  • Conversion to EURO
    The conversion to EURO takes place in the new configuration software, which we expect in the next few weeks. To realize the conversion with the COMset 2.3.19 please carry out the following steps.
    1. Save the configuration to your Harddisk.
    2. Reset the PBX to the delivery state
    3. Reload the configuration to the PBX.

Troubleshooting:

  • If you transfer a connection to a busy subscriber, the connection falls back after 6 sec. (previous settings: 3 sec.)
  • Management of several Voice Mail Centers is now possible without reservation.
  • Connection breaks during call transfers with DeTeWe Eurix-245 were fixed.

1.4 D
(Datum)

Troubleshooting:

  • Hook-Flash of 1 sec. corrected.
  • Transfer of external calls with the Xtension-module of the COMfort 2000 improved.

1.4 C
(19. 03. 01)

New features:

  • Calling line identification of incomming calls without identification impoved. ISDN-devices are now showing e.g. "unknown" (depends on the device).
  • Initiation of callbacks optimized. If one subscriber has already initiated a callback and activates it again, it'll be confirmed. If another subscriber is trying to initiate a callback on the same target, he receives a busy signal.
  • Sporadically a COMfort 2000 could not be found on the bus.This Problem was fixed with the firmware revision 1.2H for the COMfort 2000.
  • Announcement function, can now be enabled for every single subscriber.
  • The display message "for/from" for the smar-tel-i was enabled.
  • Call transfer with the DeTeWe Euromaster on a busy subscriber is possible from now on.
  • Voice Mail Center functions implemented.
  • Function key "RUF 3" of the smar-tel-i corrected.

Troubleshooting:

  • Firmware revised.

1.2 J
(02. 04. 00)

Troubleshooting:

  • Firmware revised.
  • When the COMfort 2000 was expanded with a Xtension-module, sporadically the dial-tone was missing. This was fixed.
  • The following proceeding for the update via configuration software is to be observed:
    COMmander Basic was put into operation or extended with 8a/b-modules and the internal dial tone is missing.
    - download the file com12j.exe from our internet site to a folder you like and expand the file by doubleclick.
    - connect the PBX to the serial port of your PC and start the configuration software COMmander set.
    - Safe the configuration file to your harddisk.
    - Load the flash file to the PBX by using the menue item "File->write flash to the PBX". The configuration file in the PBX should not be affected.

1.2 H
(29. 02. 00)

New features:

  • Text before answering.
  • Soft-LCR 3.0 can be used entirely.

1.2 G
(10. 01. 00)

Troubleshooting:

  • Firmware revised
  • Subscriber were switched off sporadically. This was fixed.
  • Remote functions revised
  • Door can be opened by analog devices again.
  • ISDN-devices with keypad function are now again enabled to program the PBX.
  • Blind call transfer during call forwarding revised.
  • Dial tone can be detected even in case of direct excange line access.

Clever Ideas